Search Results

The development and calibration of modern combustion engines is challenging in the area of continuously tightening emission limits and the necessity for meeting real driving emissions regulations. A focus is on the knowledge of the internal engine processes and the determination of pollutants formations in order to predict the engine emissions. A physical model-based development provides an insight into hardly measurable phenomena properties and is robust against changing input data. With increasing modeling depth the required computing capacities increase. As an alternative to physical modeling, data-driven machine learning methods can be used to enable high-performance modeling accuracy. However, these are dependent on the learned data. To combine the performance and robustness of both types of modeling a hybrid application of data-driven and physical models is developed in this paper as a grey box model for the exhaust emission prediction of a commercial vehicle diesel engine.

In order to reduce the negative health effects associated with engine pollutants, environmental problems caused by combustion engine emissions and satisfy the current strict emission standards, it is essential to better understand and simulate the emission formation process. Further development of emission model, improves the accuracy of the model-based optimization approach, which is used as a decisive tool for combustion system development and engine-out emission reduction. The numerical approaches for emission simulation are closely coupled to the combustion model. Using a detailed emission model, considering the 3D mixture preparation simulation including, chemical reactions, demands high computational effort. Phenomenological combustion models, used in 1D approaches for model-based system optimization can deliver heat release rate, while using a two-zone approach can estimate the NOx emissions.

The homogeneous Diesel combustion is a way to effect a soot and nitrogen oxide (NOx) free Diesel engine operation. Using direct injection of Diesel fuel, the mixture typically ignites before it is fully homogenized. In this study a homogeneous mixture is prepared outside of the combustion chamber by a Cool Flame Vaporizer. At first the specification of the vaporizer is given in this paper. To determine the composition of the vaporizer gas an analysis using gas chromatography/mass spectroscopy (GC/MS) was made. The results give an idea of the effects on engine combustion. Followed by, the vaporizer was adapted to a single-cylinder Diesel engine. To adapt the engine's configuration regarding compression ratio and inlet temperature range a zero dimensional engine process simulation software was utilized. The engine was run in different operating modes.

Specific shifting of load points is an important approach in order to reduce the fuel consumption of gasoline engines. A potential measure is cylinder deactivation, which is used as a study example. Currently CO2 savings of new concepts are evaluated by dynamic cycles simulations. The fuel consumption during driving cycles is calculated based on consumption-optimized steady-state engine maps. Discrete load point shifts occur as shifts within maps. For reasons of comfort shifts require neutral torque. The work of deactivated cylinders must be compensated by active cylinders within one working cycle. Due to the larger time constant of the air path the air charge must be increased or decreased in order to deactivate or activate cylinders without affecting the torque. A working-cycle-resolved, continuously variable parameter is prerequisite for process control. Manipulation of ignition timing enables a reduction of efficiency and gained work.

The latest legislative tendencies for on-highway heavy duty vehicles in the United States such as the feasibility assessment of low NOX standards of CARB or EPA’s memorandum forecast further tightening of the NOX emissions limits. In addition, the GHG Phase 2 legislation and also phased-in regulations in the EU enforce a continuous reduction in CO2 emissions resp. fuel consumption. In order to meet such low NOX emission limits, a rapid heat-up of the exhaust after-treatment system (EATS) is inevitable. However, the required thermal management results in increased fuel consumption, i.e. CO2 emissions as shown in numerous previous works also by the authors. A NOX-CO2 trade-off for cumulative cycle emissions can be observed, which can be optimized by using more advance technologies on the engine and/or on the EATS side.

Hydrogen engines offer the possibility of a carbon neutral transportation - a focal point of current propulsion development activities especially for EU and US future concepts. From today's point of view, hydrogen can play an important role in this regard as it is a carbon-free fuel, no CO2 emissions are produced during its combustion process. Besides, it can be well used for lean burn combustion leading to very low NOx emissions, a key benefit in combination with an optimized after-treatment system for future ultra-low NOx legislations of heavy-duty (HD) engines. Comprehensive investigations using experimental tests and model-based development approach are performed using a six cylinder HD hydrogen engine featuring PFI (port fuel injection) aiming the definition of a high efficiency hydrogen engine concept.

Internal combustion engines with lean homogeneous charge and auto-ignition combustion of gasoline fuels have the capability to significantly reduce fuel consumption and realize ultra-low engine-out NOx emissions. Group research of Volkswagen AG has therefore defined the Gasoline Compression Ignition combustion (GCI®) concept. A detailed investigation of this novel combustion process has been carried out on test bench engines and test vehicles by group research of Volkswagen AG and IAV GmbH Gifhorn. Experimental results confirm the theoretically expected potential for improved efficiency and emissions behavior. Volkswagen AG and IAV GmbH will utilize a highly flexible externally supercharged variable valve train (VVT) engine for future investigations to extend the understanding of gas exchange and EGR strategy as well as the boost demands of gasoline auto-ignition combustion processes.

The newest legislative trends enforce a significant decrease in CO2 emissions for commercial vehicles. For instance, in Europe a drop in fleet consumption of 15% and 30% is set as target by the regulation by 2025 and 2030. The use of carbon-neutral fuels offers possibilities regarding net-zero CO2 emissions - although not yet considered by the rules. Another challenging aspect is the drastic tightening of NOx emissions limits for future legislations, which is approved or being discussed both for the United States and for the EU. The current work describes the potentials of an innovative fuel, marketed as Gane fuel regarding performance, efficiency and emission behavior. First, the properties of the developed fuel are described: Gane is made from methanol blended with water and is tailored for diffusive combustion. The fuel blending is so defined to fulfill the combustion requirements.

Future heavy-duty (HD) concepts should fulfill very tight tail-pipe NOx emissions and simultaneously fulfill the fuel efficiency targets. In current HD Euro VII discussions, real working cycles become key to ensure emission conformity. For instance, cold start and cold ambient conditions during testing with low load profiles starting from 0% payload, require external heating measures. Knowing the trade-off between fuel consumption and tail-pipe NOx emissions a holistic engine and EAT system optimization with innovative thermal management is required. Towards a carbon neutral mobility, Hydrogen combustion engines are one of the key solutions. Advanced combustion system development enables maximal usage of lean burning as the major advantage of the Hydrogen fuel for efficiency improvement and NOx reduction.

Mixture formation in gasoline direct-injection engines is largely determined by the quality of injection. Injection systems with a wide range of layouts are used today in enhancing spray quality. As parameters, the pressure and temperature of injected fuel play a crucial part in defining quality. The effect increasing pressure has on the quality of spray is basically known. So are ways of applying this process to gasoline fuel. The effect of massively increasing the temperature of injected fuel - to the point of reaching supercritical conditions - in contrast, is not known in any detail. For this reason, the following paper focuses attention on examining the fundamental influence of increasing fuel temperature from 25 °C to 450 °C on the spray behavior of a high-pressure injector with a GDI nozzle. Combining relevant levels of pressure and temperature, discussion also turns to supercritical fuel conditions and their effects on spray behavior.

Whereas the verification of non-safety-related, embedded software typically focuses on demonstrating that the implementation fulfills its functional requirements, this is not sufficient for safety-relevant systems. In this case, the control software must also meet application-specific safety requirements. Safety requirements typically arise from the application of hazard and/or safety analysis techniques, e.g. FMEA, FTA or SHARD. During the downstream development process it must be shown that these requirements cannot be violated. This can be achieved utilizing different techniques. One way of providing evidence that violations of the safety properties identified cannot occur is to thoroughly test each of the safety requirements. This paper introduces Evolutionary Safety Testing (EST), a fully automated procedure for the safety testing of embedded control software.

One challenge for the development of commercial vehicles is the reduction of CO2 greenhouse, where hydrogen can help to reduce the fleet CO2. For instance, in Europe a drop in fleet consumption of 15% and 30% is set as target by the regulation until 2025 and 2030. Another challenge is EURO VII in EU or even already approved CARB HD Low NOx Regulation in USA, not only for Diesel but also for hydrogen combustion engines. In this study, first the requirements for the combustion and after-treatment system of a hydrogen engine are defined based on future emission regulations. The major advantages regarded to hydrogen combustion are due to the wide range of flammability and very high flame speed numbers compared to other fossil based fuels. Thus, it can be well used for lean burn combustion with much better fuel efficiency and very low NOx emissions with an ultra lean combustion. A comprehensive experimental investigation is performed on a HD 2 L single-cylinder engine.

The growing availability of different biofuels and synthetic fuels is leading to increased diversity of automotive fuels. Understanding how fuel properties affect combustion and how engine calibration strategies can compensate for variations in fuel composition is crucial for ensuring proper engine operation in this world of increased fuel diversity. This study looks at the ability to compensate for wide changes in cetane quality. Four different fuels with variations in cetane number, volatility and composition have been tested in a single cylinder engine and compared to diesel fuel. The selected operating conditions represent the entire engine map of a passenger car diesel engine. In part load the effects were investigated for conventional and premixed Diesel combustion. The results show that part load operation is especially relevant for the detection and compensation of varying fuel properties and that, depending on engine load, different control strategies have to be applied.

To meet the targets of Indian future emission legislation, an electrification and automation of today’s manual transmission technology is necessary. For this reason, IAV invented an electrified automated transmission family, based on well-known manual transmission technology. This low-cost automated manual transmission (AMT) approach is equipped with a 48 V electric machine and can be used as pure electric or hybrid drivetrain. Furthermore, it is possible to realize power shifts by using just one dry friction element. A small number of standard components combined with a low voltage electric machine and an electromechanical actuation system is sufficient to create a maximum of flexibility to meet future emission fleet targets, without having the disadvantageous high costs for a high-voltage electric system. To detect the optimal powertrain configuration, IAV used a unique advance development tool called Powertrain Synthesis.

The future emission standards, including real driving emissions (RDE) measurements are big challenges for engine and after-treatment development. Also for development of a robust control system, in real driving emissions cycles under varied operating conditions and climate conditions, like low ambient temperature as well as high altitude are advanced physical-based algorithms beneficial in order to realize more precise, robust and efficient control concepts. A fast-running novel physical-based ignition delay model for diesel engine combustion simulation and additionally, for combustion control in the next generation of ECUs is presented and validated in this study. Detailed chemical reactions of the ignition processes are solved by a n-heptane mechanism which is coupled to the thermodynamic simulation of in-cylinder processes during the compression and autoignition phases.

The powertrain electrification is currently not only taking place in public road mobility vehicles, but is also making its way to the racetrack, where it’s driving innovation for developments that will later be used in series production vehicles. The current development focus for electric vehicles is the balance between driving power, range and weight, which is given even greater weighting in racing. To redefine the current limits, IAV developed a complete e-powertrain for a racing MX motorcycle and integrated it into a real drivable demonstrator bike. The unique selling point is the innovative direct phase-change cooling (PCC) of the three-phase e-motor and its power electronics, which enables significantly increased continuous power (Pe = 40 kW from 7,000 rpm to 9,000 rpm) without thermal power reduction. The drive unit is powered by a replaceable Lithium-Ion round cell battery (Ubat,max = 370V) with an energy storage capacity of Ebat = 5 kWh.

The correct estimation of the air charge is crucial for the control of gasoline engines. This paper introduces an air charge estimation based on both physical and statistical models. For the physical model, an investigation was made to determine if the assumption of an isothermal process in the intake manifold is too strict and should be weakened to an assumption of an adiabatic process. For the adaptation of the statistical models, the Design of Experiments (DoE) method is used. The DoE method can shorten test expenses and calibration time significantly. The resulting model was tested with a 2-liter gasoline engine.

The development of energy efficient air conditioning systems for electric vehicles is an ever increasing challenge, because the cooling as well as the heating of the passenger compartment reduces the cruising range dramatically. Electric cars are usually equipped with a scroll compressor and a separate electric motor with appropriate power electronics. However, this solution is critical in terms of the installation space, the weight and also the costs. Therefore, an innovative and energy efficient drivetrain structure for electric vehicles was developed, which integrates the motor of the A/C-compressor directly into the drivetrain. Thus it is possible to switch off the compressor motor and to use the main motor for the drive of the compressor at certain driving situations. As a result, the operating point of the main motor can be shifted to a better efficiency.

Recent years have witnessed a dramatic increase in global ethanol production, while cellulosic feedstock or the algae-based production approach make more sustainable ethanol production foreseeable in many countries. The ethanol produced will increasingly penetrate the markets not only as blending component, but also as main fuel component, boosting demand for flex-fuel vehicles. One of the main challenges for flex-fuel vehicles is the cold start due to the poor vapor pressure of ethanol. This is detrimental to starting capability in DISI engines in particular, with increased cylinder wall wetting causing higher oil dilution. The most efficient solution for DISI engines is a smart injection strategy, enabling fuel vaporization during injection in the compression stroke. But this requires optimum injection parameters such as injection timing, split ratio and rail pressure.

A physics-based simulation program developed by IAV is used to calibrate the torque structure and cylinder charge calculation in the electronic control unit of SI engines. The model calculates both the charge cycle and combustion phase based on flow mechanics and a fractal combustion model. Once the air mass in the charge cycle has been computed, a fractal combustion model is used for the ongoing calculation of cylinder pressure and temperature. The progression of cylinder pressure over the high and low-pressure phases also provides information on engine torque. Following the engine-specific calibration of the model using elemental geometric information and reduced test bench measurements, the physical engine properties can be simulated over the operating cycle. The calibrated model allows simulations to be carried out at all operating points and the results to be treated as virtual test bench measurements.